---
url: /trade-config/order-setup.md
description: >-
  Choose fixed lots, % of balance or a fixed amount for position size, set how
  the size is split across layers, take-profit and stop-loss defaults, the
  always-use-my-values toggles, and bad-signal protection.
---

# Order Setup — How Your Trades Open

Order Setup is where you decide how every trade opens: how big it is, how it enters the market, and where its take-profits and stop-loss sit when the signal leaves them out. These settings live on the **Settings** page, in the **Sizing** and **Entries & exits** groups: **Size per trade**, **Entries**, **Take profits**, **Stop loss** and **Signal checks**. Set them once under **Account defaults** and they apply to every channel on that account; you can later change them for one channel, or for one topic of a forum channel, with a [preset](/presets/).

::: tip
Start simple. Set your lot size and a sensible default stop-loss, leave everything else on its default, and watch the Trade Preview. Tune one setting at a time.
:::

## Where these settings live

Open **Settings**. The **Account defaults** tab lists twelve sections in five groups. Order Setup covers these:

| Section | What it holds |
|---|---|
| **Size per trade** | How to size each trade (fixed lots, % of balance or a fixed amount), and the per-trade loss and profit limit |
| **Entries** | How the size is split across layers, entry layers, the entry zone |
| **Take profits** | How profit is taken, how many TPs to use, the TPs used when a signal has none, runners |
| **Stop loss** | The stop used when a signal has none, and what to do with a bad one |
| **Signal checks** | What TTMT does with prices that look like typos, and the Oracle |

How an *open* trade is managed lives in the **Running trades** group, covered in [Active Trade Setup](/trade-config/active-trade-setup). Each section shows the common settings first; the rest are under **More settings**, or switch the header to **Full** to see them all.

The **Explanations** switch in the header (on by default) shows the short description under each option; turn it off for a denser page. The **?** next to a setting opens its help with an example. Your choice is remembered. Each section ends with a **Which value wins** strip that lists where the value comes from, highest first. For **Size per trade** it reads: Symbol exception (if it sets a size) › Preset › Account defaults › TTMT default. For **Stop loss** it reads: Signal › Channel fallback › Symbol exception › Preset › Account defaults. **Take profits** shows one line for the TP prices and one for how many TPs. Turning on an "Always use my…" toggle changes the strip: the signal's value drops out and it reads Preset › Account defaults.

Nothing saves until you press **Save** in the save bar at the bottom, which lists every change with its own undo. **Reset section…** puts one section back to TTMT's defaults (it asks first, and still waits for Save). The **Preview** panel updates live as you change values, so you can see the effect on a sample trade before saving — see [Trade Preview](/trade-config/trade-preview).

## Position size (Size per trade)

Your position size is the single most impactful risk decision you make. **Size per trade** asks **How to size each trade** and offers three cards:

* **Fixed lots** — the same lot size on every trade, set in **Lot size** (default **0.10**, range **0.01–20**). Simple and predictable: a 0.10 trade is 0.10 whether its stop is 30 pips or 120 pips away. The trade-off is that your dollar risk changes with the stop distance — a far stop loses more than a near one at the same lot. Above 5 lots the page asks you to type the number to confirm.
* **% of balance** — you set **Risk per signal** as a share of your account balance (range **0.1%–100%**): what one signal may lose if every layer fills and the stop is hit. TTMT computes the lot from the signal's stop-loss distance so every trade risks about the same amount whether the stop is near or far. Wider stop → smaller lot; tighter stop → larger lot. Raising it above 10% asks you to type the number to confirm, so a typo can't set it. **Count broker credit as balance** (under **More settings**, shown when the account has credit) adds the credit to the balance TTMT sizes from; it can at most double the size.
* **Fixed amount** — you set **Amount per signal** (range **1–100,000**) and every trade risks that amount, lost at the stop, whatever your balance is doing. The lot is computed from the stop-loss distance exactly as in % of balance; the difference is that the budget is a number you chose rather than a share of the account, so it does not shrink after a losing week or grow after a winning one. This is the mode to pick when your risk rule is written in money.

A line under the field shows what a sample signal would size to at your current setting, so you can see the result before you save.

The amount is in **your account's own currency**, never dollars. On a EUR account, `200` means €200; on a cent-denominated account (`USC`, `GBC`) it means 200 of those cents. An account default applies the same number to every account you own, each in its own currency — under broadcast, an EUR account risks €200 and a USD account $200 from the same setting.

A line under **Amount per signal** shows what share of your balance the amount is (for example "≈ 2.0% of your €5,000 balance"), so you can see when it is large. Nothing blocks it: the platform lot ceiling and the equity check below are the hard stops.

A signal's risk level does not change this amount. In % of balance mode a signal the parser marks high risk sizes up; in Fixed amount it does not, because the amount is the figure you chose. A losing streak can still reduce it — that is the platform's own protection working in your favour, and it only ever sizes down.

All three modes are available in **Size per trade** and in a [preset](/presets/); a [symbol exception](/trade-config/per-asset-overrides) can set a different one per symbol or asset class. The full picture — how % of balance sizes across asset classes, and the safety check that rejects a trade rather than round *up* into more risk than you asked for — lives on [Risk Management](/core-concepts/risk-management#position-sizing).

**Close a trade at a set loss or profit** (under **More settings**) closes a single trade once it reaches the **Close at a loss of** or **Close at a profit of** amount, in your account currency. At least one of the two is needed. It is separate from the [daily limits](/safety-and-reliability/risk-limits-halt).

Regardless of what you set, there is a **platform lot ceiling** on the total volume of a single trade. It is always on and not something you configure — but it is a flat number of lots, the same on every account, so it does not scale to your balance, and a fixed lot that is far too large for a *small* account can sit well under it. TTMT also measures every planned trade against your equity; that check is advisory today and will refuse oversized plans once it is enforced. Details on [Risk Management](/core-concepts/risk-management#total-volume-safety-ceiling).

::: warning
The lot ceiling is a safety backstop, not a target — and not a substitute for a sensible lot size. If you mean "2% of my balance", use **% of balance**: typing `2` into **Lot size** means 2.00 lots.
:::

## How your position is spread — entry strategy and layers

In **Entries**, **Entry layers** sets how many layers to split your entry into — from **1 to 6**, default **4**. That is the only layer control you set. You do **not** choose how many orders each layer holds: TTMT works that out for you from the volume allocated to the layer and your broker's minimum lot and lot step. More size means more orders, capped at **6 orders per layer** and **36 orders in total**. So the exact order count depends on your lot size, the layer allocation, and your broker's symbol rules — "4 layers" does not imply any fixed number of orders. The full mechanics live in [Order Execution](/core-concepts/order-execution).

Layer 1 enters at the signal entry — as a market order when price is favorable, as a limit order when waiting for a retracement. Deeper layers are limit orders spread across the **entry zone**.

**How the size is split across layers** decides how much of your volume goes to each layer:

| Strategy | What it does | Best for |
|---|---|---|
| **All at once** | The whole size goes into layer 1, at the signal's entry; that layer can still hold up to 6 orders, depending on your size. It fires as market orders when price is favorable, as limits at the signal entry otherwise. | Scalping; you want in at the signal's price or not at all |
| **Even** (default) | Equal volume across all layers — 25 / 25 / 25 / 25 for four layers, before broker rounding. Balanced exposure across the entry zone. | Most signals; recommended starting point |
| **More at first** | More volume at the market layer, less at deeper layers. | Fast markets where catching the move matters most |
| **More deeper** | More volume at better (deeper) prices. | Retracement entries where you expect a pullback |

The **Entry layers** row sits below the strategy cards. It is disabled when you choose **All at once**, which is always one layer. As you change your lot size and layer count, a **viability badge** shows how many of the resulting orders will actually execute — if your lot size is too small to fill every order, the badge warns you and suggests a larger size.

For example: with Even and 4 layers, a BUY that retraces 60 pips fills all four layers at progressively better prices and averages your entry down. With All at once, only layer 1 exists — it fills at the signal's entry or you miss the move.

::: info How the order count is worked out
For each layer, TTMT takes that layer's share of your total volume, rounds it against your broker's lot rules, then splits it into however many orders the volume supports — capping the layer at 6 and the whole trade at 36. As an **example** (not a promise): 0.10 lots across 4 Even layers with a 0.01 minimum lot gives layer volumes of 0.03 / 0.03 / 0.02 / 0.02, which is 3 + 3 + 2 + 2 = **10 orders**; 0.12 lots across the same 4 layers gives 0.03 each, or 3 + 3 + 3 + 3 = **12 orders**. Bigger size fills more orders — watch the viability badge.
:::

```mermaid
flowchart TD
  S[Signal] --> L1[Layer 1<br/>market or limit<br/>at signal entry]
  S --> L2[Layer 2<br/>limit in entry zone]
  S --> L3[Layer 3<br/>limit, deeper]
  S --> L4[Layer 4<br/>limit, zone edge]
  L1 --> TP[Orders assigned<br/>to take-profit levels<br/>by TP Strategy]
  L2 --> TP
  L3 --> TP
  L4 --> TP
  TP --> SL[Stop-loss applied<br/>to the trade]
```

## Entry zone — how wide trades reach for a fill

The entry zone is the price band where the limit orders sit. **Entry zone width** (under **More settings** in **Entries**, shown with two or more layers) has two modes:

* **% of the stop** — **Zone width** is your percentage of the stop-loss distance minus a 5-pip buffer TTMT keeps in front of the stop (default **80%**, range **20% to 100%**).
* **Fixed pips** — a constant pip width (range **5 to 200**). On a signal whose stop is closer than this width plus 5 pips, the zone is shortened so the deepest layer stays 5 pips in front of the stop; the settings page tells you which stop size that is, and how many of each channel's recent signals had one.

The page previews the result live; for example, with a 60-pip stop in % of the stop mode at 80%, the zone is 44 pips (80% of 55). (As the UI puts it, 60 pips is about $6.00 of price distance on Gold.)

For example: a 50-pip stop in % of the stop mode at 80% gives a 36-pip entry zone. Set it to 100% and the zone widens to 45 pips — the widest it can go, with the deepest layer 5 pips in front of the stop — catching deeper retracements, but tying up margin longer. A stop within 5 pips of the entry is placed as a single entry.

For multi-layer trades, **Widen the zone toward TP1** nudges the zone toward take-profit by **Widen by** — **1 to 20 pips**, below TP1 (starts at 5 when you turn it on) — to catch near-miss entries. For example, a signal whose entry was 1 pip from filling when price reversed would have filled with the zone widened by 5 pips. See [Entry Zone Expansion](/core-concepts/entry-zone-expansion).

The only width guard is a plausibility check: the entry zone cannot be wider than **5 times your stop-loss distance**. There is no asset-class percentage cap on zone width.

## Take-profit defaults and strategy

A trade can have up to **6 take-profit levels**. In **Take profits**, **How profit is taken** controls how your volume is distributed across them:

| Strategy | Distribution shape | Best for |
|---|---|---|
| **Most at first TPs** (default) | Front-loaded — closes most volume at the nearest targets, securing profit early. Closes about 30% at the first target. | Choppy markets; banking profit fast |
| **Equal** | Even split — every target gets roughly the same share. | No strong view on how far price travels |
| **Most at last TPs** | Back-loaded — holds most volume for the furthest targets, letting winners run. | Trending pairs and high-confidence signals |

**How many TPs to use** decides how many targets you use:

* **As the signal** (default) — use however many take-profits the signal sends, whether that is 2, 3, or 5.
* **1 to 6** — fill in missing levels or drop extras to match the count you choose.

For example: a channel sends 3 take-profits but you choose 6 — TTMT fills in three more levels beyond them. Choose **As the signal** to honor the channel's 3.

**Take profits when the signal has none** holds TP1 to TP6 and is only used when a signal omits its targets. By default they are 20 / 40 / 60 / 80 / 100 / 120 pips (range **2 to 1500**). **Measure TPs in** (under **More settings**) switches the unit between **Pips** and **% of stop**, where 100% means a 1:1 target. Both sets of numbers are kept, so switching back restores your pips. The unit applies to take profits only; the stop loss is always in pips. A channel's own fallback targets (set on its [Setup page](/channels/channel-settings)) only fill TP levels you have not set here; because TP1 to TP6 always hold values, they rarely apply.

Two more settings handle fast markets:

* **If price is already past a TP at entry** — when price has already passed a market order's target by the time the order lands: **Use the next TP** (default) tries the next target, and the next, until it finds a valid one; **Close at once** books profit at market. For example, if price spiked past the first target before the market order landed, **Use the next TP** aims at the second target instead of closing instantly for a few pips.
* **Let the last TP run without a target** — when on, signals that mark a target as "open" or "runner" create positions with no take-profit. Off by default. See [Runners](/trade-config/runners).

::: warning
Letting the last TP run without a target creates positions with no take-profit. They close at their stop-loss, by the trailing stop, by a channel close message, by your daily loss limit or a per-trade limit if you set one, or when you close them yourself. Read the [Runners](/trade-config/runners) page before turning it on.
:::

## Stop-loss defaults and handling

In **Stop loss**, **Stop loss when the signal has none** is the stop distance in pips (range **5 to 500**, default **60**) used when a signal omits its stop. A stop you set for one channel is used first. A channel default that TTMT set is used only when you have not saved a stop of your own. It is measured from the price the trade enters at: with one entry layer and a signal that gives an entry range, that is the edge of the range your order rests at (or the live price, if the market is already inside the range), not the live price outside it.

**If the signal's stop looks wrong** (under **More settings**) decides what to do when the signal's stop looks wrong:

* **Use my stop** (default, safer) — auto-correct a suspected typo by applying your default stop instead.
* **Trust the signal** — use the signal's stop as-is, even if it looks suspicious.

A stop is treated as suspect if it is on the wrong side of the entry, if it lands *inside* the entry zone of a trade with several entry layers, or if it sits *more than 5 times* past your farthest take-profit. With **one entry layer** the whole trade enters at a single price, so a signal's stop is judged against that price rather than against the whole range the signal posted: a stop inside the range is kept as long as it is on the correct side of your entry and at least **5 pips** from it. Closer than 5 pips, it is treated as suspect. For example, a channel typos a stop at 1.0850 when entry was 1.08500 (a missing zero). With **Use my stop**, TTMT ignores the broken value and applies your 60-pip default instead of a 5,000-pip stop.

**Cancel waiting orders when the stop is hit** (default **on**) pulls any still-pending limit orders for a trade the moment its stop fires. For example, your stop hits on a 4-layer trade with two layers still pending; this cancels those limits so the market does not re-fill you into the same losing trade after you have been stopped out.

::: success
Cancelling waiting orders on the stop is on by default and prevents a common trap: getting re-entered into a trade you were just stopped out of, simply because price drifted back into your entry zone.
:::

## Always use my values — trust your settings over the channel's

Three on/off toggles, all **off by default**, replace the signal provider's value with yours. Each sits under **More settings** (or **Full**) in the section it belongs to, and each exists both as an account default and as a [preset](/presets/) setting:

* **Always use my zone, not the signal's** (**Entries**) — use your zone width instead of the signal's. Meant for channels that send unreliable entry ranges.
* **Always use my stop, not the signal's** (**Stop loss**) — replace the channel's stop-loss with your default stop pips, measured from where your first order rests. With several entry layers, a signal's entry range that would reach your stop is shortened so the deepest layer stays 5 pips in front of it; your stop is not moved.
* **Always use my TPs, not the signal's** (**Take profits**) — replace the channel's targets with your default take-profit pips.

Turn these on for a channel whose levels you do not trust. For example, a momentum channel sends entries with no stop; with **Always use my stop** off you simply get your default for the missing value, but turn it on in a preset for a different channel if it sends stops you actively distrust. For how and when an override is applied, see [Override Modes](/core-concepts/override-modes).

::: danger
Overriding a channel's stop-loss or take-profits means you stop trusting its levels entirely. Make sure your defaults suit that channel's instrument and style before turning these on.
:::

## Bad-signal protection (Signal checks)

TTMT screens every signal for malformed prices — decimal slips, stale copy-paste, a stray digit. In **Signal checks**, **When a signal's prices look wrong** decides what happens to a price that fails the check on the signal that opens the trade:

* **Correct them** (default) — replaces a wrong-looking stop loss or entry with your default stop distance and tells you. A wrong-looking take profit is different: on this first signal it is left exactly as posted, and only gets corrected once a follow-up updates it.
* **Skip the signal** — skips the whole signal rather than guessing at a replacement.
* **Use as sent** — trades the stop loss, entry, and take profits as posted.

One line holds no matter which of the three you choose: a price more than **10x** the current market (or less than a tenth of it) is never traded as posted — **Correct them** and **Use as sent** swap it for a safe one, **Skip the signal** does not trade the signal. That is the single exception every setting shares.

With **Correct them**, **Only fix prices when the trade still pays at least** appears (under **More settings**) — a target-to-stop ratio shown as "× its risk" (range **0.1 to 2.0**, default **0.3**). Signals whose targets are wide but internally consistent get a lighter touch; lower values fix more signals.

For example: a channel posts SELL XAUUSD, entry 4392–4397, stop loss 4442 — about 500 pips from the entry. **Correct them** places the stop at your default distance (4398) and tells you; **Skip the signal** does not trade the signal at all; **Use as sent** trades the posted 4442.

Below these sits the Oracle, a second opinion on each signal; see the [Oracle](/oracle/) pages.

For the full picture of what TTMT catches and how, see [Signal Validation](/safety-and-reliability/signal-validation).

## Ideal Settings & Trading Strategy

### Scenario 1 — Conservative Copy-Trader

**Setup:** A new user on a $2,000 personal account following one well-known complete-signal gold/forex channel.

**Settings:** Fixed lots 0.05. Even, 4 entry layers. Entry zone width "% of the stop" at 80%. Widen the zone off. Most at first TPs, How many TPs to use "3." Stop loss when the signal has none 60 pips, take profits when the signal has none 20 / 40 / 60. If the signal's stop looks wrong "Use my stop," Cancel waiting orders when the stop is hit on. All three "Always use my…" toggles off (trust the channel). When a signal's prices look wrong "Correct them," threshold 0.3. If price is already past a TP at entry "Use the next TP," Let the last TP run without a target off.

**Why:** Small fixed lots and most-at-first take-profits bank profit early while you learn how the channel behaves. Trusting the channel's levels but keeping "Correct them" on means typos are caught without second-guessing good signals.

**Watch for:** At 0.05 lots across 4 layers, the viability badge may warn that deep-layer orders are too small to fill. Accept fewer fills or raise the lot size slightly.

**Switch when:** You have watched 20-plus trades and trust the channel — move to the Moderate setup to capture more of the trend.

### Scenario 2 — Moderate / Balanced Trader

**Setup:** An experienced user, $10,000 account, following two or three forex channels of mixed quality.

**Settings:** Fixed lots 0.20. Even, 4 entry layers. Entry zone width "% of the stop" at 90%, Widen the zone toward TP1 on, widen by 5 pips. Most at first TPs, How many TPs to use "As the signal." Stop loss when the signal has none 50 pips, take profits when the signal has none 25 / 50 / 75 / 100 / 125 / 150. If the signal's stop looks wrong "Use my stop," Cancel waiting orders when the stop is hit on. Always use my stop on for the weakest channel only (via its preset). When a signal's prices look wrong "Correct them," threshold 0.3. If price is already past a TP at entry "Use the next TP," Let the last TP run without a target off.

**Why:** A modest fixed lot keeps risk predictable across instruments. Keeping the signal's own targets honors good providers, while widening the zone recovers near-miss entries. Overriding the stop on one weak channel via its preset contains the damage without touching the good channels.

**Watch for:** "As the signal" means a channel that sends 6 take-profits spreads your volume thin. If you prefer to bank earlier, cap it at 3.

**Switch when:** A channel proves consistently unreliable on its levels — move it to a preset with the "Always use my…" toggles on, or add a [symbol exception](/trade-config/per-asset-overrides) if the problem is instrument-specific.

### Scenario 3 — Prop-Firm Scalper

**Setup:** A trader on a $100,000 prop-firm challenge account following a fast alert-then-details scalping channel on indices and gold, with tight drawdown rules.

**Settings:** Fixed lots 0.30 (sized to stay well under the firm's per-trade risk). More at first, 3 entry layers (more volume at market — fast fills matter). Entry zone width "Fixed pips" at 25 pips, Widen the zone off. Most at first TPs, How many TPs to use "2." Stop loss when the signal has none 25 pips, take profits when the signal has none 15 / 30. If the signal's stop looks wrong "Use my stop," Cancel waiting orders when the stop is hit on. Always use my stop on (the drawdown rules demand your own tight stop). When a signal's prices look wrong "Correct them," threshold 0.3. If price is already past a TP at entry "Close at once" (scalps move fast — take the small win), Let the last TP run without a target off.

**Why:** Putting more volume at market captures fast scalps before they run; a tight fixed zone and 2 quick targets match the channel's style. Overriding the stop guarantees every trade respects the firm's risk cap. Closing immediately when a target is already passed avoids chasing.

**Watch for:** Putting more size at the first layer means a bad entry hurts more. Pair this with the [Risk Limits](/safety-and-reliability/risk-limits-halt) daily halt so a bad session cannot blow the challenge.

**Switch when:** You clear the challenge and move to a funded account with looser rules — relax to the Moderate setup and let winners run with Most at last TPs.

## Related pages

* [Active Trade Setup](/trade-config/active-trade-setup) — what happens to a trade after it opens
* [Per-Asset Overrides](/trade-config/per-asset-overrides) — symbol exceptions: a different size and stop/target pips per symbol or asset class
* [Runners](/trade-config/runners) — the "Let the last TP run without a target" setting in depth
* [Trade Preview](/trade-config/trade-preview) — see these settings applied to a sample trade
* [Override Modes](/core-concepts/override-modes) — how and when an override is applied
* [Presets](/presets/) — change Order Setup for one channel
